How To Ptex Skis?

How do you use PTEX?

Fill in the GougeUsing your propane torch or butane lighter, fire up one tip of the P-Tex candle.Wait until it’s flaming (this may take a couple of minutes). … Move the molten P-Tex candle to the gouge. … Do a second round if necessary then extinguish the flame.Let the P-Tex cool about 15 minutes.More items…

Do you need to wax after PTEX?

Registered. Definitely before waxing. As you thought, PTEX candles are made of the same material as the base is made of… so you want the clean the gouge area of any dirt, debris or wax… if you can lightly sand the area to give the new PTEX material some surface to stick on to.Dec 27, 2011

Why is my PTEX cracking?

Overfilling a deep hole in one hit can cause the ptex to crack. Once the ptex is cool to the touch (5-10 min), you can begin scraping back. Holding your metal scraper at an angle, start scraping from the front to the back of the ski. Vary the direction of each pass, so that you’re removing material evenly.Jan 26, 2016

How do you get PTEX to stick?

P-tex falling out?Clean the edges of the gouge and remove any loose material.Sand the core shot to roughen it for better adhesion.Get a cheap soldering iron to melt in the repair material.Melt in a layer of copolymer/metalgrip – this is a more rubbery material that adheres well to coreshots and metal.More items…•Nov 20, 2012

What temperature does PTEX melt?

CAUTION! A P-Tex candle burns very hot (>970 F); Severe burns can result if dripped on skin. Ventilate room if you recently used fluoro waxes. Hold the candle close to the base to reduce carbon (black) formation from the burning process (see important notes at the bottom of the page).

How long does it take for P-TEX to dry?

After filling all of the damaged spots with P-Tex wait five minutes to let the P-Tex cool and harden. 6. Once the material has cooled scrape off the excess with a sharp metal scraper.Jun 15, 2017

Can you wax an extruded base?

Waxing an extruded base won’t make as much difference as waxing a sintered base will. Therefore it is not necessary to wax as often. For example an un-waxed extruded base (EB) will actually be faster than a an un-waxed sintered base (SB). A waxed SB on the other hand will be faster than a waxed EB.May 30, 2019

What is ski PTex?

P-tex is the abbreviated name for Polyethylene. There are 10 major classifications of Polyethylene. For snowboards and skis the form used is UHMWPE or Ultra-high-molecular-weight polyethylene. It’s the same material used to make bullet proof jackets as well as hip and knee replacements.

How do you sharpen ski edges?

These seven steps will take your ski edges from dull to razor sharp.Find a good location.Secure your skis in the ski vises.Deburr the edges.File the side edges.File the base edges.Polish the edges.Detune the tip and tail.Oct 20, 2019

Does PTex stick to epoxy?

The p tex will not stick to the epoxy. Sand the base repair flush or get a stone grind. Any DIY splitboard has multiple epoxy spots on the base. It will have little effect on the board.Nov 22, 2013

How do you fix a core shot on a ski?

Light a Fire. Hold your lighter to one end of the P-tex stick until it’s flaming. Then, hold the stick close to the base of the ski and spin it as you drip the melted substance into the hole while moving the stick steadily but slowly along the damaged area.Nov 23, 2019

How do you base weld skis?

Cut away any hanging or loose pieces of base material that will no longer serve any purpose.Take your lighter and begin heating the P-Tex stick. … Core Shots. … Now that the ski is clean you are going to need base weld or sometimes called metal bond. … Begin pressing firmly down on the base weld using the metal scraper.More items…•Apr 17, 2014

Do you need to remove old wax before waxing skis?

Just spray it on and clean off with a rag. If you are just wanting to wax your skis then apply hot wax and scrape it off before it cools, that cleans up the base. Then apply wax a second time and allow to cool before scrapping. There is no need to use wax remover before waxing.

What to clean skis with before waxing?

Base cleaners also tend to remove any wax that you did had left on your bases, which isn’t ideal. For my part, I simply start with a solution of warm water and a little mild washing-up liquid. Clean the bases of your skis with a soft sponge and allow them to dry fully before you start waxing.Feb 8, 2016

Can you use rubbing alcohol as base cleaner?

Clean the ski or board’s base, using a citrus based wax remover/ski base cleaner. You can also use rubbing alcohol or lemon/orange peel. Just remember to also wash down the base afterwards if you use peel.

How often should I wax my skis?

At a minimum, you should wax them once at the start of every season. However, if you’re a frequent skier it also makes sense to wax them once more during the season.Apr 30, 2021

Is there a difference between clear and black PTEX?

There’s different grades of Ptex but if you’re just using the standard candle either or will use and being that the board is black the clear will only have a minimal discoloration.Apr 20, 2010

What is PTEX made of?

P-Tex, on the other hand, is made of an ultra-high-molecular-weight version of polyethylene (UHMW for short). This means that each chain of ethylene molecules is very, very long: hundreds of thousands of repeat units long, in fact. These long chains make the material very resistant to impact (i.e., hard).Jan 22, 2015

What is ski base cleaner made of?

Manufacturers are also allowed to keep proprietary chemical descriptions pretty vague. But here we can see in Section 3, the main ingredient (80-100%) in Swix base cleaner is Hydrocarbon, C9-C10, n-alkanes, isoalkanes, <2% aromatics.Jan 2, 2021

Can you melt PTEX with an iron?

It’s better to get ptex repair ribbon (doesnt contain wax) and a ptex gun or iron, or even cheaper a soldering iron which you then use to melt the ptex in, you can heat up the base a little bit too for a better bond. Just make sure to do it in a really well ventilated area preferably outside with a mask on.Sep 25, 2018

What is a Panzer file?

Panzer Body File – A very aggressive cutting file used primarily for removing excess base material and flattening bases. Nicknamed as the tuner’s chainsaw.

Are old skis still good?

You can technically ski on an old pair of skis for as long as they are intact and can attach to your ski boots – but if you want to get the best from your expensive lift pass – you probably should upgrade to a new pair at least every 6-12 years. More major improvements in design tend to happen every 5 years.Feb 15, 2019

Do old skis have value?

The older and longer the skis, the more valuable they are. Signatures, race logos and manufacturers’ names add value. A wood ski is usually preferable to people buying for decorating reasons.Sep 19, 1998

Is there a market for old skis?

Take Your Skis to a Local Ski Shop Browse ski shops near you and see if they accept used skis. They might be able to sell them on consignment for you and take a percentage of the sale as a commission, or you might be able to trade them in for a discount on better equipment.Jan 12, 2019